Welcome, Guest
Username: Password: Remember me
  • Page:
  • 1

TOPIC: Counting Tray

Counting Tray 2 months 3 weeks ago #1

I've been slogging away counting my tokens for my next transmute and i've been wondering if anyone has found a good "off the shelf" tray to quickly count 25s for moots. I'm sure I could rig up something, but I tend to like to go way over engineered, and/or it'd be nice to be able to do multiple stacks of 25 ready to go to be bag up at a time. The various tube and token holders I have are either over or under sadly.

I can't be the only one who's thought about this - I'm just hoping someone else has been more successful in a solutiion.
"Not So Exclusive" "Exclusively" Elf Wizard

Also run as "MElf - a Thor Wielding Tank"!

Please Log in or Create an account to join the conversation.

Counting Tray 2 months 3 weeks ago #2

Druegar had someone 3D print one IIRC.
First ever death in True Horde
"Well, with you guarding 2 players, that means you take 90. Are you dead?"
-Incognito

My token shop/trade thread: Wade's Wide World of Wonder 

My Current Paladin Build 

Please Log in or Create an account to join the conversation.

Counting Tray 2 months 3 weeks ago #3

Wade Schwendemann (Dr. Uid) wrote: Druegar had someone 3D print one IIRC.


100% he has some. I had a friend make a different one for me with some alterations and I mainly need to 1) find the file and 2) print them.
~Rebecca

The Dragon's Horde aka our tokens for sale/trade
truedungeon.com/forum?view=topic&catid=583&id=253588

Please Log in or Create an account to join the conversation.

Counting Tray 2 months 3 weeks ago #4

Take a clear token tube, put 25 tokens in, mark it with a line, empty token tube into a baggie, repeat.
Please check out my trade post located here!

Please Log in or Create an account to join the conversation.

Last edit: by Guedoji.

Counting Tray 2 months 3 weeks ago #5

I have seen Druegar using the trays he has. They are really cool. Would be a good item for Trent and TD Tavern to carry in their stores.

Please Log in or Create an account to join the conversation.

Counting Tray 2 months 3 weeks ago #6

My husband can 3D print them, either in a one column or a three column. They’re sized just right for 25 tokens and the three column version is stackable, if that’s useful. Depends on if you’re just counting or looking to store them that way.

This message has an attachment image.
Please log in or register to see it.

Please Log in or Create an account to join the conversation.

Last edit: by Hallie Smith. Reason: Adding picture

Counting Tray 2 months 3 weeks ago #7

Wade Schwendemann (Dr. Uid) wrote: Druegar had someone 3D print one IIRC.

Quite a few, actually.
They were designed and printed by forumite Kenban. Here's the post he made about them a little over three years ago:

Kenban wrote: I made this really quickly. To cut down on the size I overlapped the rows, each division is offset to the side by 5 mm from center. 4 rows wide is the most you can fit on most consumer 3D printers.

Have you looked it up in the TDb ?
Please post TDb corrections in this thread .
If I write something in teal, it should not be taken seriously

Please Log in or Create an account to join the conversation.

Last edit: by Druegar.

Counting Tray 2 months 3 weeks ago #8

Was the .stl ever provided?
Please check out my trade post located here!

Please Log in or Create an account to join the conversation.

Last edit: by Guedoji.

Counting Tray 2 months 3 weeks ago #9

To the best of my knowledge, Kenban has not open sourced it. But I very much recommend contacting him. He's just a PM away...
Have you looked it up in the TDb ?
Please post TDb corrections in this thread .
If I write something in teal, it should not be taken seriously

Please Log in or Create an account to join the conversation.

  • Page:
  • 1
Time to create page: 0.178 seconds